Grab overhead crane with a grab bucket handling bulk material

Grab Overhead Crane

Table of Contents

A grab overhead crane is a bridge crane fitted with a grab bucket for loose bulk material. It picks up scrap metal, coal, ore and raw material without slings or manual loading. Steel plants, scrap yards and power plants use it to feed furnaces, fill hoppers and clear stockpiles. The bucket itself is covered on our grab bucket page.

This guide explains how the system works, which grab types exist, and how to choose one.

How a Grab Overhead Crane Works

The crane runs on rails above the material yard or bay. The trolley carries a hoist that opens and closes the grab. The operator lowers the open bucket onto the pile, closes it to scoop, lifts, travels to the target and opens it to drop the load.

This cycle repeats many times per hour, so the crane must be built for continuous use.

Types of Grab Buckets

  • Double rope grab: one holding rope and one closing rope, run by a two drum hoist. This is the common choice for bulk handling.
  • Four rope grab: two holding ropes and two closing ropes. It is more stable and suits large buckets and heavy loads.
  • Motor grab, also called electro hydraulic grab: the bucket has its own motor and hydraulic unit, fed by a cable. It needs a simpler hoist and gives good control, but adds cable handling.

Pick the type by material, bucket size and how often the crane works.

Grab overhead crane with a grab bucket handling bulk material

Matching the Bucket to the Material

Bucket volume and material density decide the lifting load. A bucket holding one cubic meter of coal weighs far less than one holding the same volume of scrap or ore. Always calculate the full load as bucket weight plus material weight.

  • Light bulk such as coal and ash: larger bucket volume
  • Heavy bulk such as ore and heavy scrap: smaller volume and a stronger bucket
  • Irregular scrap: a grab with teeth, or a design made for mixed shapes

Duty Class and Structure

Grab cranes are among the busiest cranes in a plant. They often run most of the shift. Under GB/T 3811 they commonly sit in the upper part of the A1 to A8 scale, and A6 to A8 is often discussed for continuous grab duty. A double girder overhead crane is the usual base, because it carries the heavy trolley and shock loads well. GB 6067 sets the safety rules, and FEM 1.001 helps buyers map the class.

Features That Help in Dusty Plants

  • Sealed motors and electrical boxes to keep dust out
  • A cabin with filtered air, or remote control from a clean room
  • Anti sway control, so the grab lands where it should
  • Overload limiter and limit switches
  • Wear checks on hoist parts and crane wheels built into daily rounds

How to Choose a Grab Overhead Crane

  • Material type, density and lump size
  • Grab volume and lifting rate per hour
  • Span, lift height and stockpile layout
  • Duty class based on real shift hours
  • Dust, heat and moisture exposure
  • Cabin or remote control, and operator view

Nybon Machinery supplies double girder overhead cranes for steel plants and bulk handling bays, with grab hoists sized to your material. Send your data on the contact page.

A scrap bay often sits beside a melt shop, where a foundry overhead crane handles the molten metal.

FAQs

What is a grab overhead crane?

It is an overhead bridge crane fitted with a grab bucket, used to pick up and move loose bulk material such as scrap, coal and ore.

Which grab type is best?

A double rope grab suits general work. A four rope grab fits large buckets and heavy loads. A motor grab gives fine control but needs a cable system.

What duty class does a grab crane need?

Grab cranes often work most of the shift, so many sit in a high class such as A6 to A8 under GB/T 3811. Check it against your real cycle count.

How do I size the grab bucket?

Start from the material density and the lift rate you need. Then add the bucket weight to the material weight to get the rated load.

Picture of NYBON MACHINERY
NYBON MACHINERY

Henan Nybon Machinery Co., Ltd
Professional Crane Manufacturer & Exporter Based in Xinxiang, Henan, China.